01
Day
:
21
Hours
:
53
Minutes
:
06
Seconds
Back to blog
November 19, 2026

How Loud Should My Mix Be Before Mastering?

Quick answer: Do not try to make your mix loud before mastering. Make it sound finished, with healthy dynamics and peaks that stay comfortably below 0 dBFS. Advice on headroom varies: Abbey Road's mastering engineers ask for at least 2 to 3 dB on the rendered file, and other guides suggest 3 dB or more, up to 6 dB, so ask your mastering engineer for their spec. Do not leave a mastering-style limiter on the master bus, bounce a 24-bit file in the same format as your session, and treat LUFS as a result and not a target. A dynamic mix often lands around -18 LUFS, but there is no single correct number.

This guide explains what to aim for, why, and how to check it before you bounce. If you are still sorting out where mixing ends and mastering begins, start with Mixing vs Mastering: What's the Difference?

Why a mix should not be as loud as a master

Loudness is the job of the final stage. A mastering engineer needs room to work, and a mix that is already pushed against a limiter leaves none. As mixer William Wittman puts it in a Production Expert guide, nothing is "left for" mastering except levelling, so the mix should sound complete before it goes. What matters is balance, tone and dynamics, not level.

Loudness is also not a competition anymore. Streaming platforms normalize playback, so a master pushed far past a platform's target is simply turned down. We cover the master side in How to Make a Loud Master Without Destroying Your Mix and in Dave Kutch loudness targets. For the limiting stage, see Limiter vs Clipper.

Peak headroom: how much to leave

Headroom is the distance between your loudest peak and 0 dBFS. The numbers you will read differ, so here is what the main sources say:

SourceWhat it advises
Abbey Road mastering engineersAt least 2 to 3 dB of headroom on the rendered file
A Sonarworks guideNotes that some engineers argue for 3 dB and others for 6 dB or more
Production ExpertA 24-bit file with a generous amount of headroom, without any need to chase -18 dBFS peaks

That last point is worth a note. Some mastering services quote very low peak levels, such as -18 dBFS. According to Production Expert, that figure comes from an analog line-up level, so there is no technical need to keep your digital peaks that low. In practice, the safe approach is to leave a few dB, avoid clipping, and ask your mastering engineer which spec they prefer. Turning down a clipped bounce does not remove the clipping.

Loudness: LUFS is a result, not a target

Production Expert's guide says music mixers can treat loudness targets as an aim and not a rule. Mixer Steve DeMott says he does not mix to a target, but that his mixes tend to land around -18 to -17 LUFS, which he attributes to careful calibration of his monitoring. A Sonarworks guide notes that a dynamic pop or rock mix through an analog console will probably measure about -18 LUFS, while in-the-box mixes can be much louder before mastering.

The practical conclusion: use LUFS to understand your mix, not to push it. Let the integrated reading settle across the whole song, and look at how loud the sections are relative to each other. Our sister company Process.Audio explains the three loudness windows in LUFS Explained, and True Peak vs Sample Peak covers the difference between peaks. Their Decibel plugin shows LUFS, true peak and dynamics, and there are free options too.

If you want to see how a mixer manages level during the mix, Austin Seltzer sets a LUFS reading with only drums and bass before he adds other elements, so the mix bus is never overloaded. He explains it in his Inside the Mix series, and we summarize it in Why Your Mix Bus Limiter Is Killing Your Low End.

What to do with the master bus

  • Bus compression. Many engineers mix into a bus compressor from the start, and that is fine if it is part of the sound. Adding "a little gloss" at the end rarely helps, Production Expert warns, because it fights your fader moves. Abbey Road suggests mixing with bus compression if you want to hear its effect, but leaving the final compression off when you render. Opinions differ, so mention it to your engineer.
  • Limiter. Abbey Road says to take off any digital limiting. Production Expert allows a limiter only as protection against stray peaks, with the threshold at 0 dB and a ceiling around -1 dBTP, and says it is not needed for a mix that will be mastered.
  • EQ across the whole mix. Unless you want a specific unified treatment, you can fix tone on the individual tracks.

Control the dynamics yourself

A mix should be as dynamic as the music needs, but it should already contain your intent. According to Production Expert, small rides on the mix bus fader between sections can reduce large dynamic gaps and give mastering a better starting point. For the mix itself, our complete stem mixing workflow video with Fab Dupont shows how to manage a mix's dynamic range and make mixes loud with less damage.

Trust your monitoring

A mix that sounds wrong on the engineer's system often goes back because of inaccurate monitoring, not because of a bad decision. Check on several speakers and in mono. Our loudness monitoring tip shows how to use an SPL meter to keep your listening level consistent, so your mixes translate more reliably.

Before you bounce: a checklist

  1. Listen on several systems and in mono. Fix balance problems now, not in mastering.
  2. Remove clicks, pops and clipping. A clipped mix bus is the fastest way to have a mix sent back. Filter subsonic rumble on suspect tracks, starting around 20 to 40 Hz.
  3. Take off the final limiter, or keep it only as clip protection, and agree on it with your engineer.
  4. Leave headroom. Ask for their spec. If they have none, a few dB below full scale is a safe default.
  5. Bounce at the session's format. A 24-bit WAV at the same sample rate as your session. Do not normalize and do not export an MP3.
  6. Bounce when you are fresh. After a break, not at the end of a long day.
  7. Label the files and add notes. Name and number the songs, and add a text file with any fades, hidden tracks or concerns. Stems can be useful as a backup for a tight deadline.
  8. Finish your alternates first. Vocal up or down versions should be decided before you send the final candidate.

Sharing files and versions is easier when everything lives in one place. Mixup, a storage and collaboration system for music and video makers, lets you share the bounce with your mastering engineer, collect feedback and approvals, and keep version control.

Learn from mastering sessions

FAQ

How loud should my mix be before mastering?

Not loud. Aim for a finished-sounding mix with healthy dynamics and peaks comfortably below 0 dBFS. Loudness is the mastering engineer's job.

How much headroom should I leave?

Abbey Road asks for at least 2 to 3 dB. Some engineers prefer 3 dB and others 6 dB or more. Ask your mastering engineer.

What LUFS should my mix be before mastering?

There is no required value. Some mixers say their dynamic mixes land around -18 to -17 LUFS, and in-the-box mixes can be louder. Treat it as information, not a target.

Should I leave a limiter on the master bus?

Most guidance says to remove it before bouncing. If you keep one, use it only as clip protection and tell your engineer.

Should I send a 16-bit or 24-bit file?

24-bit, in the same format as your session. A 24-bit file gives mastering much more room than a 16-bit one.

Should I normalize my mix before sending it?

No. Normalizing changes the file without adding anything.

Do I need to send stems?

Not always. They can be a useful backup if there is only one chance because of a deadline. Ask your mastering engineer.

Want to hear what mastering engineers do with a mix? Watch the free Puremix videos, or see the Puremix plans. For a structured path, take Foundations of Compression or the Core Audio Certification Program on Campus.

Disclosure: Puremix, Campus, Mixup and Process.Audio are sister brands. Decibel is a Process.Audio product. Technical details come from Puremix sessions and published preparation guides from Abbey Road, Production Expert and Sonarworks, checked in November 2026.

Written by Jose Carlos Arregui
Learn to record, produce and mix from the engineers behind the records.