05
Hours
:
33
Minutes
:
10
Seconds
Back to blog
November 17, 2026

Limiter vs Clipper: Which One for Loudness?

Quick answer: A limiter turns the gain down when the signal approaches a ceiling. A clipper does not turn anything down: it cuts the waveform at a threshold and shaves off the very tip of the peak. For loudness, a clipper is often used first to remove the short peaks that eat headroom, and a limiter comes last as a safety net that keeps the signal under the ceiling. A soft clipper bends the peaks gently and tends to be more transparent. A hard clipper cuts them sharply and is harsher. Use light settings, match levels when you compare, and let the limiter do as little work as possible.

This guide compares the two tools, explains the order they usually go in, and shows how to judge the result, with examples from Puremix sessions by Austin Seltzer, Brian Lucey and Dave Kutch. If you are still deciding where mixing ends and mastering begins, start with Mixing vs Mastering: What's the Difference?

Limiter vs clipper at a glance

 LimiterClipper
How it worksGain reduction: it turns the whole signal down when it hits the thresholdIt cuts the waveform at the threshold and leaves the rest untouched
TimingTakes time to react, even with a fast attackActs instantly on the peak
Effect on the rest of the mixA loud kick pulls everything down with itOnly the tip of the peak changes
Typical side effectPumping and ducking if pushed hardDistortion if pushed too far
Usual positionLast in the chain, as a ceilingBefore the limiter

What a limiter does to your mix

A limiter reacts to peaks by lowering the level of everything that goes through it. In modern pop, hip-hop and dance music, the kick and the bass are the loudest and most transient elements, so they are what trigger it. The result can be pumping, or a ducking feeling every time the kick hits.

Austin Seltzer demonstrates this on the mix bus of "Sugar Free Venom" in his Inside the Mix series. He pushes a maximizer by +2 dB, then removes it and uses a trim plugin at +2 dB instead, with nothing catching the output. The level and the bass hit stay the same, but the pumping and dipping disappear. We summarize the full session in Why Your Mix Bus Limiter Is Killing Your Low End.

What a clipper does, and soft vs hard clipping

A clipper simply cuts the waveform at the threshold. Because those peaks are very short transients, removing them frees headroom without touching the body of the sound. In Austin's session, clipping the mix bus by a modest 1 to 3 dB is something you do not hear as distortion, because the clipping artifacts are spread across the whole mix and masked by its density. What you hear is the effect: a louder mix that does not pump.

The difference between soft and hard clipping is the transition between the linear region, where the output matches the input, and the clipping region. Published comparisons generally describe soft clipping as the more transparent option for gentle gains in loudness, and hard clipping as harsher and better for deliberate character. One example is the iZotope guide What is soft clipping? Sources are not unanimous, and many of them come from plugin makers, so treat their settings as starting points.

Clipping is not free. Used too hard, it adds audible distortion and costs punch. Austin stresses that the clipper is for shaving peaks, and he still prefers hitting the mix bus harder and doing less limiting.

The usual order: clipper first, limiter last

A common approach is to place a soft clipper before the final limiter, so the clipper catches the highest peaks and the limiter reacts in a more controlled way. Many engineers do it, but it is not a rule, and sources differ on the details. What is consistent is the role of the limiter at the end:

  • The limiter is the safety net. Austin keeps the final output limiter transparent, at a ceiling of -0.1 dBTP, because the clipper has already handled the aggressive transients.
  • Mind the true peak. For streaming, Dave Kutch advises keeping the True Peak level at or below -1 dB to avoid distortion when the file is converted to a streaming format. See Dave Kutch loudness targets.
  • Control dynamics before the limiter. Compression and clipping earlier in the chain let a limiter catch only occasional peaks. A limiter that grinds down every transient sounds crushed. See How to Make a Loud Master Without Destroying Your Mix.

Austin also starts his gain staging from the bottom: he targets a specific LUFS reading with only drums and bass before adding other elements, so the output stage has very little left to do by the end.

How loud do you need to go?

Less than you might think. Streaming services use loudness normalization, so a master pushed far above a platform's target is simply turned down. Dave Kutch says loudness targets are "the last thing I'm thinking about when I'm mastering", and focuses on what sounds good. Restraint is also visible in the work of Brian Lucey, who in Limiting and Saturation runs a limiter on a mild setting, with the threshold at -1.4 dB. To see his whole approach, watch Royal Blood "How Did We Get So Dark?" - mastering, where he re-masters a record from start to finish, or his Mastering philosophy & techniques. Fab Dupont covers eight essential mastering tools in The tools used for mastering.

Which one should you use?

SituationStart withWhy
The mix pumps when the kick or 808 hitsLess limiting, or a clipper for the peaksThe limiter turns down the whole mix on every hit
You want a little more level, transparentlyA soft clipper, 1 to 3 dBIt removes short peaks without gain-reduction pumping
You need a guaranteed ceiling for deliveryA limiter with a true-peak ceilingIt guarantees the signal stays under the limit
You want deliberate grit or characterA hard clipperIt is harsher by design, so use it on purpose
The master is loud but flatBack off both and go back to the mixLoudness mostly comes from the mix, not from the output stage

How to judge the result

  1. Match the levels. The louder version will always seem better at first, so compare at the same loudness.
  2. Bypass often. Check that you are improving the mix and not only making it louder.
  3. Listen for the breathing, not the clipper. Does the kick still hit hard after it lands? Does the vocal stay present when the bass blooms? Does the energy stay consistent from hit to hit?
  4. Stop when the punch goes. Back off at the moment transients start to dull or distortion creeps in.
  5. Measure the true peak. Check the ceiling after the last processor.

To measure, see our sister company Process.Audio's guides True Peak vs Sample Peak and Control Your Dynamic Range in Real Time Using a Limiter. Their Decibel plugin shows Integrated, Short-Term and Momentary LUFS, True Peak and a dynamics measure, as Kutch's post notes. For other options, see the best metering plugins of 2026.

Keep every version of the master organized

Loudness decisions are easier when you can compare versions and collect feedback in one place. Mixup, a Puremix storage and collaboration system for music and video makers, lets you share files, gather feedback and approvals, and keep version control, so the artist or client can listen to each master and you always know which one is final.

FAQ

What is the difference between a limiter and a clipper?

A limiter lowers the gain when the signal reaches a threshold. A clipper cuts the waveform at the threshold without lowering the rest of the signal.

Is a clipper better than a limiter for loudness?

Neither is better in general. A soft clipper is a common way to remove short peaks before the limiter, and the limiter stays as the final ceiling. Use light settings and compare at matched levels.

What is the difference between soft and hard clipping?

The curve where the signal starts to be clipped. Soft clipping bends the peaks gradually and is usually more transparent. Hard clipping cuts them sharply and sounds harsher.

Should the clipper go before the limiter?

Many engineers put a soft clipper before the final limiter, so the limiter reacts in a more controlled way. It is a common approach, not a rule.

How much clipping is too much?

Austin Seltzer says modest clipping of 1 to 3 dB on the mix bus is not audible as distortion. Stop as soon as you hear the punch fade or distortion appear.

What true peak ceiling should I use?

Dave Kutch advises keeping the true peak at or below -1 dB for streaming. Austin Seltzer sets his final limiter ceiling at -0.1 dBTP, which is a different stage of his chain, so follow your delivery specs.

Do streaming platforms make my loud master quieter?

Loudness normalization turns down songs above a platform's target, so pushing far past it costs dynamics without making the song sound louder.

Want to see how engineers handle loudness in real sessions? Watch the free Puremix videos, explore Austin Seltzer's Inside the Mix episode, or see the Puremix plans. To understand dynamics processing in depth, take Foundations of Compression on Campus, or the Core Audio Certification Program.

Disclosure: Puremix, Campus, Mixup and Process.Audio are sister brands. Decibel is a Process.Audio product; the other plugins mentioned are from independent developers. Details come from Puremix sessions and published comparisons, checked in November 2026.

Written by Jose Carlos Arregui
Learn to record, produce and mix from the engineers behind the records.